Introduction
Polaroid Polapan Type 667, 3.25"
x 4.25", Black and White Pack Film is a high-speed, medium contrast,
medium-grain, general purpose black and white coaterless print film. It
is designed for low-level ambient lighting conditions and high-speed events
that require fast film. It is the film used in the PhotoScreener
Camera.
Product
Overview and Description
Each packet of Polaroid instant pack film contains all of the elements needed
to produce instant pictures. Inside, for each picture, there is a film assembly
consisting of a light-sensitive negative, a positive sheet, a "pod"
containing the developer, and tabs, which are pulled to activate the developing
process. The rollers inside the camera or film holder are used to break
the pod and spread the developer between the exposed negative and positive
sheet.
Product
Use and Procedure
 |
Handle
film packs by their edges to avoid damaging film surfaces, the pod
or the developer inside.
|
|
Keep the film in
its wrapper until you are ready to use it. Tear open the film wrapper
along the printed arrow.
|
|
Load the film into
the PhotoScreener camera by turning the camera over with the left
side down. Open the film-back by pulling out on the bottom of the
door latch. The film door will swing down out of the top part of the
film-back. Remove the empty film case by pulling out and down on the
white, foam backed tab. Place the new film in the cartridge into the
film slot with the black protective cover tab sticking out. The black
tab of the film safety cover should extend through the door latch.
Check to be sure that the smaller white tabs are not tucked under
the pack. Close the film door and press the door latch into the locked
position. Pull the black tab of the safety cover all the way out of
the film-back and discard it.
|
|
After an exposure
(picture) is made, pulling the white tab all the way out moves the
exposed negative from the focal plane behind the lens to a position
facing the positive sheet. Simultaneously, the larger tab of the film
assembly is positioned between the rollers, and sticks out of the
camera where it can be grasped.
|
|
Pulling the large
tab drags the film assembly-negative, pod and positive sheet, through
the rollers. The pod bursts open and the developer is spread between
the positive and negative. It is important to pull the tabs straight
and at a steady, moderate speed to ensure the developer is spread
evenly.
|
|
Development begins
immediately, outside the camera film holder. After the proper development
time, the finished picture is peeled away from negative.
|
|
When you pull out
a film image it has a paper image covering it. You peel this paper
cover off and there is a sticky residue surrounding the photo. This
can be peeled off to reveal a clean photo underneath (the sticky residue
is attached to the white square sticker surrounding the photo and
should be removed and disposed). You may want to have a paper towel
or tissue available to wipe your fingers after peeling off the paper
image and white border sticker.
|
|
Process exposed
film promptly. Be aware that development time and the temperature
of the film affect picture quality. Ideally Polaroid film should be
developed at about 70-75°F (21-24°C). |
The 3 Critical Keys to Quality Images
| 1. |
Keep
the processing rollers in the camera clean |
|
|
Inspect and clean
the roller surface regularly |
|
|
Use a soft non-abrasive
cloth |
|
|
Clean tab slot |
|
|
High volume users,
Polaroid recommends rollers be cleaned every 3-5 packs. After several
years you may need to replace roller. |
| 2. |
Note
the temperature and development time accurately |
|
|
Process at 70-75°F
(21-24°C) |
|
|
Check tip sheet
packed with Polaroid or download Film Data Sheet, which gives processing
times and temperatures. |
| 3. |
Pull
the film tabs straight |
|
|
Film should be pulled
parallel to the camera back. |
|
|
Pull at a steady,
moderate speed. Saying the word "Polaroid" is a good way
to time the speed of the pull. |
For Complete Usage Information, Troubleshooting
Hints and Quick Tips download operating user guide: "A
Guide to Using Polaroid Instant Pack Films".
www.polaroid.com/service/userguides/photographic/packfilms_guide.pdf
Adobe Acrobat required.
Features
and Benefits
|
High speed, medium-contrast,
medium-grain, general-purpose black and white coaterless print film. |
|
Designed for low-level
ambient lighting conditions and high-speed events that require a fast
film. |
|
Crisp, clear image. |
|
More widely used
then discontinued Type 337 Film, resulting in cost savings. |
Frequently
Asked Questions
| Q: |
Why
has the Polaroid Type 667 Film replaced the old Type 337 Film? How
is the new film different? |
| A: |
Polaroid recently
discontinued production of the Type 337 instant film previously used
in the PhotoScreener. The Type 337 Film had limited uses and infrequent
production runs at Polaroid. The replacement film is the Type 667.
It is a more affordable film that provides a clearer image and is
less expensive than the Type 337. Type 667 requires the manual removal
of the picture (it is a peel apart film) versus the automatic photograph
discharge with the Type 337.
|
| Q: |
How
do I know that the replacement film will not get cancelled in the
future like the Type 337 Film? |
| A: |
Polaroid Corporation
stated that the Type 667 Film would be supported indefinitely. Polaroid
has many applications in the commercial marketplace employing the
Type 667 Film. These markets include medical, photography, publishing
and more.
|
| Q: |
If
I do not manually pull my photo out of the camera, can another picture
be taken? |
| A: |
Yes, you should
pull your photo out after taking your set of pictures. In the event
you forget and do another screening, the second set of eyes will "double
expose" your first picture. (This is important to remember for
retrofit users since the unit does not automatically eject).
|
| Q: |
Why
is processing time so important? |
| A: |
Processing effects
contrast and density to some extent. A picture processed for too short
a time will have dull grays, mottle and have little contrast. If maximum
density is required, the processing time may be extended by 15 seconds
(for example process for 45 seconds rather then 30 seconds). This
may increase the contrast and density, but may also result in some
loss of gray.
|
| Q: |
Does
it speed the drying process to wave the film back and forth? |
| A: |
Never wave developing
film back and forth in an attempt to keep it warm or cool or speed
drying. This could adversely affect image quality. Also, be careful
not to bend or squeeze developing film.
|
| Q: |
Will
I lose the entire pack of film if I pull a tab and another one does
not appear? |
| A: |
In this situation,
remember these steps:
|
Do not pull
another tab |
|
Carefully
open the back of the camera so that you can place a finger on
the edge of the film pack inside. Hold the pack in position
and open the back all of the way. (You can open the camera without
spoiling additional film, provided you do so away from bright
light and do not move the pack of film). |
|
Gently remove
any crumbled film tabs and discard them. |
|
Inspect and
clean the rollers thoroughly. Clean the tab slot, too. |
|
Unfold the
top white tab so it sticks out. Close the camera back securely.
Resume picture taking. |
|
| Q: |
There
is a caution note on the Type 667 Film Packaging. How harmful are
the chemicals? |
| A: |
The processing chemistry
in the pod of both films (Type 337 and Type 667) contains alkali and
could cause some discomfort, particularly to the eyes or mouth, if
you were to come in contact with it. During the processing cycle the
alkali moves toward neutral and becomes relatively harmless. Type
667 has been around since the early 1960's and Polaroid is not aware
of anyone having a skin irritation problem with the processing chemistry.
|
Technical
Specifications
| Film
Speed: |
ISO
3000/DIN 36 |
| Format: |
3.25
x 4.25 in. (8.5 x 10.8 cm) pack film |
| Image
Area: |
2.88
x 3.75 in. (7.3 x 9.5 cm.) |
|
Finish: |
Glossy |
| Exposures: |
10
exposures per pack/2 packs per box |
| Development
Time and Temperature: |
30
seconds at 75°F (24°C) |
Articles / Sales Brochures
/ Manuals
Type
667 Film User Guide: "A Guide to Using Polaroid Instant Pack Films".
Material
Safety Data Sheets: MSDS #: M-0625 (7 pages).
Developer fluid contained in pod of film types, including the Type 667.
Film
Data Sheet for T-667 Black and White Pack Film
Adobe Acrobat is required to view or print the above.
Click the icon below to download a free copy.
Warranty
Always use Polaroid film before the expiration date stamped on the package.
Outdated film may not produce satisfactory results and is not covered
by the Polaroid film warranty. Polaroid will replace defective film before
the expiration date.
Other
Information
Storage
Recommendations and Cautions
|
Always use Polaroid
film before the expiration date stamped on the package. Outdated film
may not produce satisfactory results, and it is not covered by the
Polaroid film warranty.
|
|
Store Polaroid film
in a cool, dry place. Unopened film may be refrigerated in its sealed
wrapper. Do not freeze film.
|
|
Before opening
film that has been refrigerated, allow it to reach room temperature.
This will take about 2 hours.
|
|
Avoid leaving film
or a loaded camera in direct sunlight, or in a hot, humid place, such
as the trunk or glove compartment of a car. High temperatures and
humidity can affect picture quality. |
|
Please read the
"Caution Notice" printed on Polaroid film packages. Here's
what it says: "This process uses caustic paste. Avoid contact
with skin, eyes and mouth and keep away from children and animals.
If you get some paste on your skin, wipe it off immediately and wash
with water to avoid an alkali burn. If eye or mouth contact occurs,
quickly wash the area with plenty of water and see a doctor. Keep
discarded materials away from children, animals, clothing and furniture.
|
|
Please dispose of
used negative and packaging materials properly.
|
Product
Ordering Information
|
